Uçuş Kaydı göndermek için ".igc" dönüşümü
Moderatör: Moderatör Ekibi
- PaRaDoX
- Mesajlar: 712
- Kayıt: 31.07.2004, 23:53
- Ad Soyad: Ali Yücer
- Şehir: Ankara
- :
- Aldığı Beğeni: 40 / 1
- Yaş: 41
- Pilot Menüsü:
Uçuş Kaydı göndermek için ".igc" dönüşümü
Merhaba arkadaşlar
Uçuş Kaydı göndermek için .igc dosya uzantısına ihtiyacımız var.
GPS imizdeki verileri nasıl .igc ye çevireceğimizi bu konuda toparlamak istedik.
Kağan Akçalar'ın .igc dönüşümü için hazırladığı yazıyı yayınlıyorum.
Kendisine teşekkürü bir borç biliriz
Sizde eksik gördüğünüz yerleri anlatırsanız bu dönüşüm için tam bir rehber yazı hazırlamış oluruz.
Once gpsteki bilgileri pcye aktarmak lazim www.gpstm.com dan Trackmaker programini indirmeli.
Programi acip "Interface" menusunden cihazin markasini
secerek gps ile veri alisverisi penceresini aciyorsunuz.
"product id"e basarak pcnin gpsinizi gormesi ve tanimasini sagliyorsunuz.
Olmazsa:
- kablo?
- gps acik mi?
- gpste ki setup menude interface secenegini kontol edin. Mesela garmin marka gps ise bu secenek gpste de"garmin" olmali, bazen NMEA da kalmis olabiliyor.
- kablo pcde dogru porta mi bagli? digerlerini dene
- 1available ports seceneginde digerlerini secmeyi dene
- "tools" "options" "comm port" kisminda "auto detection
denebilir.
Save as diyip altindaki dosya formatini "OziExplorer files (plt. trk.rte)" olarak degistirin.
Kaydedilen dosyalarin arasindan TRK veya PLT uzantili olanini CompeGPS veya OziExplorer gibi bir programla acin.
Uygun bir menuden bu dosyayi ICG olarak kaydedin.
Uçuş Kaydı göndermek için .igc dosya uzantısına ihtiyacımız var.
GPS imizdeki verileri nasıl .igc ye çevireceğimizi bu konuda toparlamak istedik.
Kağan Akçalar'ın .igc dönüşümü için hazırladığı yazıyı yayınlıyorum.
Kendisine teşekkürü bir borç biliriz
Sizde eksik gördüğünüz yerleri anlatırsanız bu dönüşüm için tam bir rehber yazı hazırlamış oluruz.
Once gpsteki bilgileri pcye aktarmak lazim www.gpstm.com dan Trackmaker programini indirmeli.
Programi acip "Interface" menusunden cihazin markasini
secerek gps ile veri alisverisi penceresini aciyorsunuz.
"product id"e basarak pcnin gpsinizi gormesi ve tanimasini sagliyorsunuz.
Olmazsa:
- kablo?
- gps acik mi?
- gpste ki setup menude interface secenegini kontol edin. Mesela garmin marka gps ise bu secenek gpste de"garmin" olmali, bazen NMEA da kalmis olabiliyor.
- kablo pcde dogru porta mi bagli? digerlerini dene
- 1available ports seceneginde digerlerini secmeyi dene
- "tools" "options" "comm port" kisminda "auto detection
denebilir.
Save as diyip altindaki dosya formatini "OziExplorer files (plt. trk.rte)" olarak degistirin.
Kaydedilen dosyalarin arasindan TRK veya PLT uzantili olanini CompeGPS veya OziExplorer gibi bir programla acin.
Uygun bir menuden bu dosyayi ICG olarak kaydedin.
- gorkemc
- Mesajlar: 1
- Kayıt: 15.08.2007, 13:08
- Ad Soyad: Gorkem Canverdi
- Şehir: İstanbul
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
GPS ucus datasinin IGC formatina cevrilmesi
Merhabalar,
CompeGPS ve OziExplorer ucretli yazilimlar. Herkes satin alamayabilir. Bu sebeple ucretsiz yazilimlarla GPS datasinin IGC formatina nasil donusturulebileceginden asagida bahsetmeye calistim, umarim faydali olur.
IGC donusumu icin gereken yazilimlar:
- GPS Trackmaker - v13.0 (http://www.gpstm.com)
- GPS Babel - v1.3.4 (http://www.gpsbabel.org)
2.d adiminda sectiginiz cikis dosyasina IGC formatina donusturulmus ucus bilgileriniz kaydedilmis olmali. Kolay gelsin
Gorkem
Not: Sadece GPSBabel yazilimini kullanarak da bu islemi yapabilirsiniz.
CompeGPS ve OziExplorer ucretli yazilimlar. Herkes satin alamayabilir. Bu sebeple ucretsiz yazilimlarla GPS datasinin IGC formatina nasil donusturulebileceginden asagida bahsetmeye calistim, umarim faydali olur.
IGC donusumu icin gereken yazilimlar:
- GPS Trackmaker - v13.0 (http://www.gpstm.com)
- GPS Babel - v1.3.4 (http://www.gpsbabel.org)
- 1. GPS Trackmaker yazilimi ile GPSinizdeki ucus bilgilerini bilgisayara aktarip GPS Trackmaker dosyasi (gtm) olarak kaydedin.
2. GPSBabelGUI programini calistirip acilan pencerede
- a. Input kismindaki Format'i GPS TrackMaker olarak secin.
b. Input kismindaki File'a 1.adimda gtm olarak kaydettiginiz dosyayi girin.
c. Output kismindaki Format'i FAI/IGC Flight Recorder Data Format olarak secin.
d. Output kismindaki File'a istediginiz bir cikis dosyasi ismini verin.
e. Tracks kutucugunu secin.
f. let's go butonuna basin.
2.d adiminda sectiginiz cikis dosyasina IGC formatina donusturulmus ucus bilgileriniz kaydedilmis olmali. Kolay gelsin
Gorkem
Not: Sadece GPSBabel yazilimini kullanarak da bu islemi yapabilirsiniz.
- m.bayrakci
- Mesajlar: 331
- Kayıt: 04.07.2006, 21:40
- Ad Soyad: Murat Bayrakçı
- Şehir: memleket:Tire Yaşadığı:Diyarbakır
- Aldığı Beğeni: 2 / 0
- Yaş: 48
- Pilot Menüsü:
arkadaşlar garmin 60csx ile yapmış olduğum kaydı gpsbabel programı ile direk IGC formatına dönüştürdüm. Oldukça kolay oldu. İlgili program linki(ücretsiz) : http://www.gpsbabel.org/
Ayrıca bayılacağınızı düşündüğüm bir program daha buldum. Bu program yardımıyla üretmiş olduğunuz ICG dosyasını yükleyerek sanki go pro kameradan çekilmişcesine bir uçuş görüntüsü izleyebilirsiniz. Linkini aşağıda veriyorum. Görüntüde ayrıca uçuş datalarınıda sol yanda takip edebiliyorsunuz.(ücretsiz)
http://ywtw.de/igcsimen.html
yorumlarınızı bekliyorum
murat bayrakçı
Ayrıca bayılacağınızı düşündüğüm bir program daha buldum. Bu program yardımıyla üretmiş olduğunuz ICG dosyasını yükleyerek sanki go pro kameradan çekilmişcesine bir uçuş görüntüsü izleyebilirsiniz. Linkini aşağıda veriyorum. Görüntüde ayrıca uçuş datalarınıda sol yanda takip edebiliyorsunuz.(ücretsiz)
http://ywtw.de/igcsimen.html
yorumlarınızı bekliyorum
murat bayrakçı
- süleymanhoca
- Mesajlar: 15
- Kayıt: 15.04.2007, 21:27
- Ad Soyad: Süleyman Ürkmeztürk
- Şehir: Manisa
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
- acg5
- Mesajlar: 307
- Kayıt: 23.09.2004, 22:11
- Ad Soyad: Adnan Coskun Gücenmez
- Şehir: Mersin
- Aldığı Beğeni: 3 / 1
- Pilot Menüsü:
http://www.gpsvisualizer.com/gpsbabel/
Bu adresten proğram yüklemeden değiştirebiliyorsunuz.
Süleyman hocam sizin sorunuzun cevabıda orada olabilir. bir inceleyin. bu arada çok saklandınıyorsunzu... rüzgar pek esmiyorda o yüzden )))
Bu adresten proğram yüklemeden değiştirebiliyorsunuz.
Süleyman hocam sizin sorunuzun cevabıda orada olabilir. bir inceleyin. bu arada çok saklandınıyorsunzu... rüzgar pek esmiyorda o yüzden )))
- fortunatex
- Mesajlar: 1
- Kayıt: 07.08.2012, 13:13
- Ad Soyad: Bahtiyar Uzunbay
- Şehir: Antalya
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
- SkyCloud
- Mesajlar: 566
- Kayıt: 13.04.2005, 10:25
- Ad Soyad: Akin Gokbulut
- Şehir: İstanbul
- :
- Aldığı Beğeni: 20 / 0
- Pilot Menüsü:
Ucretsiz veya kullanimi ucrete tabi olmayan GpsDump programi internetten indirilerek gps'teki ucus kayitlari .IGC uzantili sekilde pc'ye kaydedilebilir. Bu programin kullanimi da oldukca kolay. Fakat ucus kayitlarindaki digital imza kayboluyor gibi.
Digital imza, ucus kaydinin icerigiyle oynanmadiginin veya degistirilmediginin bir sekilde garantisi gibi de kabul edilebilir. (Not : Sanal dunyada hic bir seyin garantisi olmaz aslinda).
Rekor ucuslari, resmi ucuslar vb ucus kayitlarinda gerektigi uzere digital imzanin da korunmasi isteniyorsa ucretli bir program olan CompeGPS kullanilabilir.
Digital imza, ucus kaydinin icerigiyle oynanmadiginin veya degistirilmediginin bir sekilde garantisi gibi de kabul edilebilir. (Not : Sanal dunyada hic bir seyin garantisi olmaz aslinda).
Rekor ucuslari, resmi ucuslar vb ucus kayitlarinda gerektigi uzere digital imzanin da korunmasi isteniyorsa ucretli bir program olan CompeGPS kullanilabilir.
- alp78
- Mesajlar: 181
- Kayıt: 06.05.2012, 19:24
- Ad Soyad: Taner Alp
- Şehir: İstanbul
- Aldığı Beğeni: 34 / 2
- Pilot Menüsü:
GPS DUMP yükledim fakat sürücüyü görmüyor. hata msj. veriyor. flymaster'ın sayfasından sürücü yüklemeye çalışıyorum. bilg. takılıyor, yükleme bitmiyor. yardım lütfen... flymaster sitesinden indirdiğim döküman aşağıda. bir sonraki adıma geçemedim.
Connecting B1nav to GPSdump
GPSDump uses a virtual com port to connect to the B1nav, so the first step is to discover
which port number has been allocated by the PC to the B1nav virtual com port.
The following steps will allow you to easily discover that com port number:
• Disconnect B1nav from your PC
• Start GPSdump, on the menu select the Misc, and "Set COM port".
• Check the available ports, and make a note of them, in this example we only have
COM1 and COM2, so the B1nav is neither of them.
• Click the "Cancel".
• Switch on your B1nav, and connect it to your PC.
• Wait a few seconds.
• Go into the "Misc" "Set COM port" again. Check the available ports. You should see
a new port which was not visible previously, in this example we now have COM5.
Page 2 of 8
Using GPSdump with B1nav
• Select the respective COM port, in the example we I will select COM5 (this is the
COM port allocated to the B1nav), and click OK.
• You should now be able to upload and download data from your B1nav.
Connecting B1nav to GPSdump
GPSDump uses a virtual com port to connect to the B1nav, so the first step is to discover
which port number has been allocated by the PC to the B1nav virtual com port.
The following steps will allow you to easily discover that com port number:
• Disconnect B1nav from your PC
• Start GPSdump, on the menu select the Misc, and "Set COM port".
• Check the available ports, and make a note of them, in this example we only have
COM1 and COM2, so the B1nav is neither of them.
• Click the "Cancel".
• Switch on your B1nav, and connect it to your PC.
• Wait a few seconds.
• Go into the "Misc" "Set COM port" again. Check the available ports. You should see
a new port which was not visible previously, in this example we now have COM5.
Page 2 of 8
Using GPSdump with B1nav
• Select the respective COM port, in the example we I will select COM5 (this is the
COM port allocated to the B1nav), and click OK.
• You should now be able to upload and download data from your B1nav.
- kakalamtahu
- Mesajlar: 174
- Kayıt: 30.10.2012, 17:46
- Ad Soyad: Hasan Tahsin Çervatoğlu
- Şehir: İstanbul
- Aldığı Beğeni: 5 / 0
- Pilot Menüsü:
- m.bayrakci
- Mesajlar: 331
- Kayıt: 04.07.2006, 21:40
- Ad Soyad: Murat Bayrakçı
- Şehir: memleket:Tire Yaşadığı:Diyarbakır
- Aldığı Beğeni: 2 / 0
- Yaş: 48
- Pilot Menüsü:
Garmin 60CSX GPS cihazım var. Birkaç yıldır düzenli olarak uçuş kayıtlarımı GPSBabel programı ile .igc formatına dönüştürüp sorunsuzca yükledim. Dün ve bugün yaptığım uçuşları yükleyemedim. Ekranda aşağıda görülen hata mesajını alıyorum.
"Uçuş bilgilerini gönderirken hata oluştu
The date of the flight is in the future
Please use the Year-month-day not the US Year-day-month format"
Uçuş kayıtlarımı yükleyemiyorum. Bu konuda ne yapmam gerekiyor?
"Uçuş bilgilerini gönderirken hata oluştu
The date of the flight is in the future
Please use the Year-month-day not the US Year-day-month format"
Uçuş kayıtlarımı yükleyemiyorum. Bu konuda ne yapmam gerekiyor?
- Zen Air Sports
- Mesajlar: 100
- Kayıt: 08.10.2009, 00:24
- Ad Soyad: Ruşen Temiz
- Şehir: İstanbul
- :
- Aldığı Beğeni: 3 / 0
- Pilot Menüsü:
yardım :)
Merhaba arkadaşlar...pazar günü yaptığım uçuşu database e eklemek için uğraşıyorum...Yukarıda ki adımlar bir kaç kez tekrarlamama rağmen ilerleme kaydedemedim.Bilgisayarım Babelin son adımında hata mesajı verdi..yardımcı olabilrseniz çok sevinirim
- SkyCloud
- Mesajlar: 566
- Kayıt: 13.04.2005, 10:25
- Ad Soyad: Akin Gokbulut
- Şehir: İstanbul
- :
- Aldığı Beğeni: 20 / 0
- Pilot Menüsü:
gpsdump programinin kullanilmasini tavsiye ederim. Daha basit ve kolay.
Oncelikle GPS driver'larinin yuklu olmasi gerekiyor.
Takip edilmesi gereken adimlar ise asagidaki gibi.
(Not : Eger cihaz Flymaster ise oncelikle yukaridaki 8 nolu mesajdaki adimlar uygulanmalidir).
Select the respective COM port, (this is the COM port allocated to GPS), and click OK.
• You should now be able to upload and download data from your GPS.
• on the menu select “Logs”
• Locate the and click on the “Read Garmin or Read Flymaster” (GPS brand)option in the menu.
• GPSdump will request the stored flights from GPS, this may take a few seconds
• Once GPSdump has the list of available flights in the GPS, it will show a “Track
list” dialog, select the flight to download and click “Ok”.
• GPSdump will start to download the flight data, you will see the “Track position” counter incrementing, and a forecasted time remaining will appear in brackets next to the counter.
• Once the flight is downloaded, GPSdump will display the list “track position records”
• You must select the track position records. To select all the entire
flight select the “Select all” option in the “Edit” menu
• Having selected the “track records”, open the “File”->”Save log in IGC format”.
• A new screen will pop up that will need bit of detail in. It's useful to use the "save with long name" as it provides a date in the file name.
• Write 001 into ‘Flight #’ and write 111 into ‘FR Serial no’ then fill in other fields up to your wish.
• click the “Save” button to save the IGC track log to disk.
Oncelikle GPS driver'larinin yuklu olmasi gerekiyor.
Takip edilmesi gereken adimlar ise asagidaki gibi.
(Not : Eger cihaz Flymaster ise oncelikle yukaridaki 8 nolu mesajdaki adimlar uygulanmalidir).
Select the respective COM port, (this is the COM port allocated to GPS), and click OK.
• You should now be able to upload and download data from your GPS.
• on the menu select “Logs”
• Locate the and click on the “Read Garmin or Read Flymaster” (GPS brand)option in the menu.
• GPSdump will request the stored flights from GPS, this may take a few seconds
• Once GPSdump has the list of available flights in the GPS, it will show a “Track
list” dialog, select the flight to download and click “Ok”.
• GPSdump will start to download the flight data, you will see the “Track position” counter incrementing, and a forecasted time remaining will appear in brackets next to the counter.
• Once the flight is downloaded, GPSdump will display the list “track position records”
• You must select the track position records. To select all the entire
flight select the “Select all” option in the “Edit” menu
• Having selected the “track records”, open the “File”->”Save log in IGC format”.
• A new screen will pop up that will need bit of detail in. It's useful to use the "save with long name" as it provides a date in the file name.
• Write 001 into ‘Flight #’ and write 111 into ‘FR Serial no’ then fill in other fields up to your wish.
• click the “Save” button to save the IGC track log to disk.
- Zen Air Sports
- Mesajlar: 100
- Kayıt: 08.10.2009, 00:24
- Ad Soyad: Ruşen Temiz
- Şehir: İstanbul
- :
- Aldığı Beğeni: 3 / 0
- Pilot Menüsü:
- aliozankamis
- Mesajlar: 3
- Kayıt: 02.03.2015, 19:06
- Ad Soyad: Ali Ozan Kamış
- Şehir: İstanbul
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
- aliozankamis
- Mesajlar: 3
- Kayıt: 02.03.2015, 19:06
- Ad Soyad: Ali Ozan Kamış
- Şehir: İstanbul
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
- aliozankamis
- Mesajlar: 3
- Kayıt: 02.03.2015, 19:06
- Ad Soyad: Ali Ozan Kamış
- Şehir: İstanbul
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
- aylayktomovitmovit
- Mesajlar: 28
- Kayıt: 13.04.2015, 20:22
- Ad Soyad: Onur Numan
- Şehir: Burdur
- Aldığı Beğeni: 0 / 0
- Pilot Menüsü:
Re: Uçuş Kaydı göndermek için ".igc" dönüşümü
iyi uçuşlar gps imin tarihi yanlıs oldugu için kayıtlar gecersiz sayılıyor tarihi değiştirebilirmiyiz ?